As promised, here is the cutting information as well as assembly. The information provided is for colors used with what is shown in the image. Make it your own and change it up. Different inks, DSP and die cuts. If you have any questions, please reach out to me.
Basic White Cardstock 3" x 2"
DSP or CS Top strip 2-1/2" x 1"
DSP or CS Middle strip 3" x 1"
DSP or CS Bottom strip 2" x 1"
DSP (for die cut design) 3" x 5"
1. Score the Basic White Cardstock at 3-1/2" and fold it in half to create the card base.
2. Adhere the three strips of DSP or CS to the card front using Multipurpose Liquid Glue. Spacing is your choice - nothing is set.
3. Die cut the large floral image or some "sprigs" as I did from the 3" x 5" DSP using the Thoughtful Wishes or Die of your choice. Adhere to the card using Multipurpose Liquid Glue. Set it aside to dry. (I used a couple pieces of double-sided Adhesive Sheets https://bit.ly/3Yq1NDB placed on the DSP before die cutting on another card, but on this one I used Mini Glue Dots https://bit.ly/3xQqWwl in the middle only as this will be hidden under the sentiment.
4. I stamped the sentiment on Basic White Cardstock in Gray Granite and created the label using the Labeled with Love Punch. Adhere to the card front with Stampin’ Dimensionals.
5. Apply embellishments to finish. I used Rhinestone Basic Jewels.
Card #2 (right) 4-¼" x 5-½"
Color of your choice ~ Cardstock card base 8-1/2" x 5-1/2" (score at 4-1/4")
Basic White Cardstock 4-1/4" x 3-1/4"
Basic White Cardstock 4-1/4" x 1"
Basic White Cardstock 4" x 4"
DSP 3" x 2" (you need 3)
1. Score the Cardstock (of your choice) at 4-1/4" and fold it in half to create the card base. I used Painted Texture embossing folder.
2. Create three labels from the three pieces of DSP or CS of your choice using the Labeled with Love Punch or Die or choose your own, then cut the labels in half.
3. On the 4-1/4" x 3-1/4" Basic White Cardstock panel, I embossed using Timeworn Type (retired) but you can emboss if you like with whatever you have.
4. I then adhered three label halves along the top of the panel (I placed the middle 1st) and the other three along the bottom using Stampin’ Dimensionals. There should be a small space between each set of label halves - maybe ¼" or so.
4. Die cut two flower images (I used sprigs) from the 4" x 4" Basic White Cardstock piece using the Thoughtful Wishes Dies or Dies of your choice. Trim the die-cut images at the bottom ends if they are too long for your placement, then adhere them to the Basic White Cardstock panel in the space between the label halves using Stampin’ Dimensionals. The bottom of the die cut images will be hidden under sentiment after being shortened, if yours are too long.
5. I stamped the sentiment in Pretty Peacock on the 4-1/4" x 1" Basic White Cardstock. Adhere to the Basic White Cardstock panel using Stampin’ Dimensionals.
6. Adhere the 4-1/4" x 3-1/4" Basic White Cardstock panel to the card base slightly higher than center using Stampin’ Dimensionals. If you prefer centered, that works too.
7.Apply a few Embellishments/Gems and you are finished.
Gift Bag (middle) 4" x 5" x 1"
(The DSP I used was striped on 1 side and floral on the other per my references below).
1. Cut the DSP of your choice at 10-1/2" x 6".
2. Turn the paper over so the opposite print (mine is floral) is facing up. Score at 1/2", 1", 1-1/2", 5-1/2", 6", and 6-1/2".
3. Turn the paper over again so the striped print (or whatever yours might be) is facing up and rotate it so the stripes are horizontal. Score at 1".
4. Cut at an angle to create wedges on both sides of the 1/2" vertical score line and at the 1-1/2" vertical score line, stopping at the 1" horizontal score line. Repeat at the 5-1/2", and 6-1/2" vertical score lines. (see images below)
5. Fold along the score lines.
6. Assemble the bag and adhere using Multipurpose Liquid Glue (or adhesive of your choice but a glue is preferred). Set aside to dry.
7. I then created the label from Basic White Cardstock using the Labeled with Love Punch or Die.
8. I stamped the sentiment in Night of Navy on label. I adhered the label to bag using Stampin' Dimensionals.
9. I tied the Iridescent Striped Trim around the top of the bag securing with a couple of mini glue dots on the back of the bag. You can embellish if you like.
Here is a reference for score lines and the snip areas for putting the gift bag together. Please note when scoring to move cardstock from right to left. Don't use the 1" and 1-½" marks on the right of scoring blade. That will mess you up - speaking from experience more than once LOL! I did use the Stampin' Up!™ paper trimmer https://bit.ly/3yYNv1X which is what I am referencing on the use above.
I hope these images help with the scoring and snipping for the gift bag.
2 comments:
It’s incredible how much work you put into this. Thank you so much!
Thank you so much. Hope you give at least one a try. I appreciate you.
Post a Comment